Armstrong Clark Oil Based Wood Deck Stains

Armstrong Clark Prepping Instructions

by Administrator

The most crucial step in any exterior wood restoration or maintenance project is to properly prep the surface before staining. Armstrong Clark Wood Stains are quality-formulated wood coatings with five generations’ worth of experience that will give your deck lasting beauty and protection.

To ensure the expected results from any of the Armstrong Clark Oil-Based Wood Stain products, the wood surface must be cleaned and prepped prior to staining.

The exterior wood surface being refinished needs to be free of dirt, grime, gray wood fibers, and old deck stain or sealer. Even new wood needs to be cleaned to remove mill glaze and contaminants. For newer or grayed-out wood, we highly recommend using Restore-A-Deck Wood Cleaner and Brightener. This two-step powder system is specially designed to clean and prepare wood for new stain.

Armstrong Clark Prepping Instructions

For wood surfaces with old deck stains or sealers, we recommend the Restore-A-Deck Stain Stripper. This product is designed to break down and soften transparent and semi-transparent wood stains so they can be washed away.

This process of cleaning or stripping the wood will ensure that the Armstrong Clark Wood Stain will penetrate the wood and perform properly. Use the simple-to-follow step-by-step instructions for either RAD product to adequately prep the wood surface.

Applying a new coat of Armstrong Clark Stain (maintenance coat) over an old coat is easy. However, prior to applying a maintenance coat of any Armstrong Clark Stain, it is still important to clean the wood surface. It is not necessary, however, to remove the old Armstrong Clark stain. Simply clean the surface using the RAD Wood Cleaner, and any old Armstrong Clark stain that remains will bond with the new stain coat.

Step two of the system follows either the RAD Cleaner or RAD Stain Stripper. The RAD step two is a Wood Brightener that counteracts the causticity of the cleaner or stripper and corrects the wood’s pH level, making it more acidic. This opens the wood’s pores and allows it to accept as much new stain as possible.

Once the exterior wood surface is ready, following the prepping instructions, allow 1-2 days for the wood surface to dry. You can expect the most from your new Armstrong Clark Oil-Based Wood Stain with proper prepping. It will enhance the wood’s beauty and give you extended use for many years.

Ask Below for Questions on Prepping for Armstrong Clark Stains

Subscribe
Notify of
guest
702 Comments
Inline Feedbacks
View all comments
Brad C
Brad C
3 years ago

Have 4 yr old redwood deck that was previously stained with the Home Depot Behr Semi Transparent Stain about 3 years ago.  Planning on sanding (to help remove stain and blemishes) and then need advice on what to do before applying your Semi Solid redwood Sequoia product – using RAD/pressure wash and how long to dry.  Also what is best way to apply this stain.  Thx, Brad

Avatar photo
3 years ago

I noticed some threads of the wood surface started peeling back when we were using a stripper on the deck. Should we sand in that case? We already stripped and brightened.

Avatar photo
Admin
3 years ago
Reply to 

No need.

Dee
Dee
3 years ago

My outdoor deck is redwood, installed over 35 years ago.  My question: Can I use Armstrong Clark Stain on this deck if I sand off the paint on it (the paint is old too!)? I would like to obtain the natural look/finish again!

Avatar photo
Admin
3 years ago
Reply to  Dee

As long as you remove all of the paint, then yes.

Avatar photo
Admin
3 years ago

That is part of the cedar knots.

Jonathan Libber
Jonathan Libber
3 years ago

I am about to re-stain my deck.  The previous two coats were Armstrong  Sierra Redwood semi-transparent stain.  This third coat is the same stain.  I plan to first use Wood Cleaner followed by deck brightener.  How long do I have to wait in between rinsing off the cleaner and then applying the brightener?  Can the deck still be wet from the cleaning when I apply the brightener, or does it have to be 100% dry?

Avatar photo
Admin
3 years ago

Brighten as soon as you are done cleaning while the wood is wet. 

Denise Zitzmann
Denise Zitzmann
3 years ago

My deck was stripped, and brightened and is now drying.  In several days we will use the semi solid stain. How do you determine whether your deck needs to be sanded, and what grit sand paper should be used?

Avatar photo
Admin
3 years ago

Do not sand. Just stain.

Denise zitzmann
Denise zitzmann
3 years ago
Reply to 

There are spots where there is still stain snd the grain seems roughed up.  Sending photos.  Will be using semi solid stain. 

Avatar photo
Admin
3 years ago

That is old stain that did not come off with the stripping. You should give it one more go with the stripper and then the brightener. Shoot for 95% removal or more. A little bit of old stain is okay as it will blend.

Denise zitzmann
Denise zitzmann
3 years ago

Stain still remains is spots and where a storage box was kept on deck.  

Wayne
Wayne
3 years ago

I am about to clean and brighten my yellow cedar deck that was installed In August 2020. If it rains on the deck between prepping and staining, will that be a problem? Or, will it be okay if Allow two days of drying after the rain and before staining? Would it be better to wait for three or four consecutive dry days for prepping then staining? Thanks. 

Avatar photo
Admin
3 years ago
Reply to  Wayne

Rain does not harm the prep. Wait 48 hours after rain to let the wood dry before staining.

Noni
Noni
3 years ago

There seems to be conflicting information for new deck prep. Your website and your answers to questions states one should use the “Restore-A-Deck Wood Cleaner,” however, your brochure “General Instructions- Surface Preparation” section states to “wash with a mild scrubbing using a mixture of 1 qt. bleach, 3 qts, water, with a maximum of a 1/4 cup of liquid dish soap per gallon. Rinse thoroughly and/or light pressure wash.” Which is the preferred method. I have a redwood deck that was installed July 2020. Thank you

Avatar photo
Admin
3 years ago
Reply to  Noni

Best way is to prep with the RAD Cleaner and then the Brightener kit.

gertrud
gertrud
3 years ago

We have a 1 1/2 year old pressure treated deck and would like to stain it now with Armstrong Clark semi  transparent wood stain. Do we have to clean AND brighten before staining? Thank you.

Avatar photo
Admin
3 years ago
Reply to  gertrud

Yes, you have to prep.

Nikki
Nikki
3 years ago

Can I use dish soap and water to remove excess stain. If so how long after application 

Avatar photo
Admin
3 years ago
Reply to  Nikki

No, that will not remove excess stain. 

Steve
Steve
3 years ago

We are working with an older cedar deck. Last year we stripped, cleaned, brightened (with “Restore”) and then stained with your “Natural Tone” stain.  
We want to do a maintenance coat this year. There is one area on the deck that after being stained was under an outdoor carpet. This area has developed black spots (refer to the picture). The rest of the deck doesn’t have the spots.
1) How should we proceed? 2) Should we not have a carpet on the deck?

Avatar photo
Admin
3 years ago
Reply to  Steve

Looks like the rug being wet caused mildew under the carpet and on top of the stain. We would suggest not using it but if you do, try removing the rug after a rain and let it dry out before putting it back. This should help reduce this from happening. This year, clean and brighten for prep and then one coat of stain.

Kp
Kp
3 years ago

I cleaned/brightened my ipe (I think) deck and I have some areas with tannin bleed, do I need to rerinse and/or brighten and let dry again before staininf or will the stain spread out the tannins to make them not noticeable? I am staining with Armstrong-Clark Amber.

Avatar photo
Admin
3 years ago
Reply to  Kp

Try the brightener again but it looks more like water stains than tannin stains. They will still show when stained.

G. Anderson
G. Anderson
3 years ago

I stripped, brightened & applied one coat of A/C hardwood amber oil stain to my mahogany last June. the finish now “looks” like there isn’t any, and appears “dirty.” In June I plan to apply another coat. Prior to re-staining, should I use your deck cleaner AND re-brighten, or just the cleaner & power wash?

Avatar photo
Admin
3 years ago
Reply to  G. Anderson

Use both cleaner and brightener.

A. Chuang
A. Chuang
3 years ago

I have a seven year old mahogany deck that needs refinishing, and the company I hired is willing to use your products but is not familiar with them. They propose to power wash the deck and sand to remove all the old stain (don’t know what the builder used, but it appears a solid red in the patches that haven’t weathered). Can they then move directly to applying your hardwood oil stain, or do they need to apply a prep product first? And their estimate includes applying two coats—is that appropriate, or should only one coat be used on mahogany? Thank you!

Avatar photo
Admin
3 years ago
Reply to  A. Chuang

Just one coat for hardwoods. Use this kit after the sanding for final prep: https://www.armstrongclarkstain.com/restore-a-deck-kit

Ron Platt
Ron Platt
3 years ago

I have a 4 year old ipe deck that I stained (twice) with Seal Once/C2 water-based stain. It failed miserably twice. Do I have to remove/strip the Seal Once prior to prepping and staining with Armstrong Clark stain for ipe decks?

Avatar photo
Admin
3 years ago
Reply to  Ron Platt

Post some pictures for prep help.

Avatar photo
3 years ago
Reply to 

This is my four year old ice deck that has been restored twice with Seal Once/C2 and failed in one season, twice.

Avatar photo
Admin
3 years ago
Reply to 

Use the RAD Stripper with both additives and then brightener. https://www.armstrongclarkstain.com/restore-a-deck-stripper

John Matthews
John Matthews
3 years ago

My 4 year old pressure treated deck has received Natural Tone twice. Last year, following the container instructions we cleaned with a bleach solution then applied the second coat. this year we want to apply Natural Oak. What prep steps must we do

Avatar photo
Admin
Julie
Julie
3 years ago

I stripped, brightened, and applied one coat of cedar semi transparent AC stain this fall to my deck. The color is reading too orange for my liking. Can I try applying a darker color over the existing coat next spring, or should I strip, brighten and start over with a new color. Thanks!

Avatar photo
Admin
3 years ago
Reply to  Julie

You would need to strip and brighten for prep.

nancy
nancy
3 years ago

I used the restore a deck system to clean and brighten deck. Looked great, by the way. Then, our deck stayed too wet to stain and now it’s been raining off and on. Has been a week since cleaning. Looks like we may have 7 days of 65-70 deg weather. If I make sure there isn’t obvious dirt on deck, can I still stain in a week? Also, if I have till Spring, do I have to use the brightener again or just cleaner?

Avatar photo
Admin
3 years ago
Reply to  nancy

Yes, you can stain this week. If you wait until Spring, you would have to clean and brighten for prep.

Teresa
Teresa
4 years ago

Hello,

I have a tiger wood deck that is about 10 years old that has not had any maintenance for last 5 years or more. There was a lot of mildew so just finished power washing (tried scrubbing first). Pictures in shade and some sun attached. I am not sure if I should use your strip and brightener or cleaner and brightener now before staining. After this next step will I need to sand it before staining with mahogany. Thanks for your help.

Avatar photo
Admin
4 years ago
Reply to  Teresa

Try the cleaner and the brightener. Sand only if needed.

David Russell
David Russell
4 years ago

I just replaced my old cedar deck with new 5/4 Cedar Board decking . Do I wait a year to stain it ?

Avatar photo
4 years ago

I am planning to stain our balcony. Do you recommend staining the underside as well?

Avatar photo
Admin
4 years ago
Reply to 

No need.

Julia
Julia
4 years ago
Reply to 

The underside does get mold/mildew. How do we minimize that?

Avatar photo
Admin
4 years ago
Reply to  Julia

Staining the underside would not prevent mildew. Just clean it periodically.

Bob Angus
Bob Angus
4 years ago

Hello, I plan on using your transparent cedar stain on my IPE deck. I would like to stain the center plank in my stairways a darker color for safety purposes. See photo. Can you recommend a method of doing this? Thank you!

Avatar photo
Admin
4 years ago
Reply to  Bob Angus

For IPE, you need one of the three hardwood colors: https://www.armstrongclarkstain.com/wood-and-decking-stains/hardwood-and-ipe-stain

Make sure to prep well first. Use the Black Walnut for the darker board.

Tom Goemaat
Tom Goemaat
4 years ago

I stained my front porch with your mahogany stain last year, very happy. Am I correct that it is recommended to do maintenance coat each year, using the RAD cleaner as the prep? Thanks

Avatar photo
Admin
4 years ago
Reply to  Tom Goemaat

Yes, correct.

SJ
SJ
4 years ago

We assumed we could use this to also
touch up our matching fence, which is coated in Cabot semi stain- there’s no way to completely strip and power wash this off the fence. what do you recommend? We now own $210 of your stain so we’re kind of stuck here.

Avatar photo
Admin
4 years ago
Reply to  SJ

You cannot apply the AC Over the Cabot so you will have to remove by sanding or stripping.

SJ
SJ
4 years ago
Reply to 

So we purchased this because it was oil based and our old kind was oil based, thinking we were doing the right thing for the fence. Do you take returns?

Avatar photo
Admin
4 years ago
Reply to  SJ

It actually does not matter if the same base. No matter what you have to remove if switching as no stain can be applied over a different brand and then expect that the new stain will be able to soak in and or adhere.

https://www.armstrongclarkstain.com/refund

SJ
SJ
4 years ago

My deck has just a bit of cabot semi transparent stain on it. Most has been sanded off. Do we have to go thru the process of stripping also?

Avatar photo
Admin
4 years ago
Reply to  SJ

Yes, all has to come off.

Rebekah
Rebekah
4 years ago

Hi! I cleaned a bit of my very dirty (but no stain/sealant) deck with an OxiClean solution, but it just wasn’t cutting it, so I’m planning to clean the rest with Behr’s All-in-One Wood and Deck Cleaner. After the deck is fully dry, can I apply the Armstrong Clark stain, or do I need to apply something before? (I’m planning to use the Hardwood “Black Walnut” stain on my softwood deck.) Thanks!

Avatar photo
Admin
4 years ago
Reply to  Rebekah

Do not use the Behr for prep. Does not work well and actually damages the wood fibers. This while pressure washing is the correct prep: https://www.armstrongclarkstain.com/restore-a-deck-kit

Rebekah
Rebekah
4 years ago
Reply to 

Is this product only available online? I really don’t want to wait that long to start the process.

Avatar photo
Admin
4 years ago
Reply to  Rebekah

We sell online only.

mike
mike
4 years ago

have 25 year pressure treated deck with numerous behr solid stain with good luck until last application, deck had many blisters and peeling like rubber strip, tried stain removers and pressure washer but didn’t work, eventually and after 3 weeks removed 95% old stain with angle grinder using diamatra wood tools, have small amount on round part of spindles, again stripper and sanding won’t remove, can i try armstrong clark semi solid on floor and railings? totally disgusted with behr and working on reimbursement, but still would love to go with oil based? thanks

Avatar photo
Admin
4 years ago
Reply to  mike

You would have to remove all to use the AC stains. They cannot be applied over a solid stain.

mike
mike
4 years ago
Reply to 

what would work, my spindles are rectangle then round back to rectangle, its the round part that is so hard to remove, spindles are about 4 inches apart making it difficult? thanks

Avatar photo
Admin
4 years ago
Reply to  mike

None of the AC stains will work. You will either have to get it all off or use a solid stain.

Pam
Pam
4 years ago

Hi
I have a cedar barrel sauna that was originally coated with a competitor’s product which did not last a year! The sauna is in western Québec. I have now power washed and sanded the sauna to get as much of the old product off as I can. I estimate that there is less than 5% of the product remaining in small areas such as joint between front panel and the door. These areas have been impervious despite multiple washes. As a barrel, this is a surface that is both horizontal and vertical. Can I go ahead with the cleaner and brightener as is?

Photos are pre-wash and post-wash.

Thanks!

Avatar photo
Admin
4 years ago
Reply to  Pam

You can go ahead with the prep and stain now.

Kirk
Kirk
4 years ago

We have a mahogany deck in good shape. Every year I wash and stain the deck. Decided to give Armstrong a try. Washed and scrubbed deck with a deck cleaner. Let it dry and then applied stain. Screwed up by not seeing instruction to strip old stain. Wiped excess stain off 24 hours later. Taking long time to dry because I didn’t strip I assume. Am I okay until next summer?

Avatar photo
Admin
4 years ago
Reply to  Kirk

As long as it dries you will be fine.

Avatar photo
4 years ago

I have a professional company that seems to be willing to use Armstrong Clark stain for me, (they usually use Sherwin Williams Super Deck) but they are hesitant to use the RAD prep products. They would want to do a powerwash with the SW cleaner and sealer followed by the Revive. Would that work with the AC stain. Deck is 7 yrs old PT wood and only had one coat of transparent AC clear on it a year after built. I really like the driftwood color and the sample on it looks good!

Avatar photo
Admin
4 years ago
Reply to 

As long as it cleans up correctly, it should be okay.

DFC
DFC
4 years ago

I have a large mahogany deck in good condition that I have stripped and brightened as instructed but it will be at least weeks before I can stain. Is that an issue and do I need to do
additional prep before staining?

Avatar photo
Admin
4 years ago
Reply to  DFC

Yes, lightly pressure wash again with the brightener.

amanda
amanda
4 years ago

I power washed and stripped my Ipe table and chairs last fall. Do I need to do any more prep now before I apply the Black Walnut stain? I have a big compressor, so I was going to use that to remove any dust or dirt on the wood. Also we have storms pop up from time to time. Will it be a problem if I stain and it rains within a day or two of application? Thanks

Avatar photo
Admin
4 years ago
Reply to  amanda

Clean and brighten for the prep. The stain can take rain about 8 hours after applying.

Joe P
Joe P
4 years ago

What is the best way to clean my cedar deck without having to restrain it afterwords. I’m not planning to restain until next year.

Avatar photo
Admin
4 years ago
Reply to  Joe P

Just use warm water and some dish soap.

Sash
Sash
4 years ago

Hi there, I prepped and put one coat of Transparent Natural Tone on a 4 year old cedar deck. Mostly it looks good, but the area around knots seems to need another coat in most areas. These pics are taken 15 hours after first coat. Should I touch up those areas with more stain? Or does it looks like it needs a second coat everywhere?

Avatar photo
Admin
4 years ago
Reply to  Sash

That is normal for knots to be lighter in color as the density of the wood is different there. You cannot spot touch up. You can try another light coat to all but not sure if that will make it go away or not.

Sash
Sash
4 years ago
Reply to 

Ok thanks. I’m not overly sensitive about the knot areas. But your reply opens another question for me… is it visible to you that it could/should get a second light coat?

Avatar photo
Admin
4 years ago
Reply to  Sash

It looks good. It would be better to add another coat next year if needed.

Jane & Doug
Jane & Doug
4 years ago

We need help fixing a big ugly problem. We built a new 1,200 SF redwood deck over the span of about a year (ending around July 2019). Then we sanded the entire surface and applied two coats of AC Redwood Tone transparent stain (one coat each on two consecutive weekends). Each time we wiped off the excess stain with rags.

Come October or November we started to find black stuff on our bare feet or shoes, which has been tracked into the house and really made a mess of the carpet. Around January we scrubbed the entire deck with a little detergent and water and a stiff broom. Everything was clean at that time, but within a month it started turning black again.

We have obtained a Restore-A-Deck cleaner/brightener kit with the intention of cleaning and then re-staining the deck. Sure don’t want to end up where we started. Please HELP!

Avatar photo
Admin
4 years ago
Reply to  Jane & Doug

You did a couple of things incorrect originally. For new wood (and sanded wood) you are only supposed to apply one coat of the stain: https://www.armstrongclarkstain.com/new-decking-and-armstrong-clark-stain

You back wiped the excess right away. This is not good as it then removes the curing-drying oils before it dries and seals in the non-drying oils. This left your stain so that it can never properly cure correctly. When dirt from your environment falls on the deck, it will then “stick” to the non-drying oils and this would lead to your traction issue on shoes, etc.

At this point, you should clean all really well with the kit and pressure washing and apply one light coat to all. Do not back wipe right away. You can if needed 24 hours later.

Mark
Mark
4 years ago

Hello. I stripped and then brightened our cedar deck about 40 hours ago (with RAD products). I was told to wait 48 hours before staining, but it rained moderately last night. Do I need to wait another 48 hours after this rain before staining? Thanks!

Mark from St. Cloud, MN

Avatar photo
Admin
4 years ago
Reply to  Mark

Yes.

Tom Goemaat
Tom Goemaat
4 years ago

I have a mahogany deck with acrylic solid deck stain (Cabot) that is not holding up at all. I used your hardwood stain on my front porch deck, also mahogany and it looks terrific. I figure I need to sand off the old stain and apply yours. Is there another step involved? I have attached two photos of the back deck showing condition and also where I did a test sand spot. Also attached a picture of my front porch with your Amber hardwood stain ( wet with water, but you get the picture.). Love your product, would appreciate your advice for the back deck. Faces due south by the way, so the sun beats on it. We are in the Boston area.

Avatar photo
Admin
4 years ago
Reply to  Tom Goemaat

Sand it all off and then use the Restore A Deck Cleaner/Brightener kits for the final prep.

Dorothy Tam
Dorothy Tam
4 years ago

The supporting pillars for our deck was cracking so my husband used adhesive to repair and then painted it using semi transparent stain from another brand without consulting me. I am not happy with the result. First, I understand from your instructions that I need to remove the stain before painting with your product. I think I will need a solid stain to cover the white adhesive but you only have semi solid stain. Will this cover the adhesive and achieve uniformity in appearance? 2nd, we painted our deck with your semi transparent stain in Cedar colour which we are happy with. What semi-solid stain colour would match that Cedar colour the best as we would like the deck to be the same colour? Thank you.

Avatar photo
Admin
4 years ago
Reply to  Dorothy Tam

No, the AC stains will not cover this or stain or the filler. You will need a solid stain.

Dorothy Tam
Dorothy Tam
4 years ago
Reply to 

Is AC thinking of selling solid stains in the future?

Avatar photo
Admin
4 years ago
Reply to  Dorothy Tam

No, they are not.

Avatar photo
4 years ago

Living on the west side of Michigan, purchased a home that has a raised pressure treated pine deck, north side of home, built in 2004. Have no idea if it was previously treated. There was no color or treatment seen when we purchased in 2015. In the past 5 weeks I have removed mold and algae from all deck boards and rails. Hard work spraying and scrubbing with Mold Armor, followed by pressure wash. Have not sanded as yet.
The wood looks white now, not blackened. Because of the whiteness, is RAD cleaner necessary? I have applied sample coloring, awaiting others to be delivered. Appears to take stain very well. Just can’t decide on a color to complement our gray sided home. Have sampled Chestnut, Rustic Brown, and Natural Oak. Awaiting sample cans of ST Cedar, Trans Cedar Tone, and Trans Natural Tone.

Any suggestions would be appreciated.

Avatar photo
Admin
4 years ago
Reply to 

Pictures?

fgmaloziec@chartermi
fgmaloziec@chartermi
4 years ago
Reply to 

Pictures taken 3 weeks ago.

Avatar photo
Admin
4 years ago

Your prep looks good.

fgmaloziec@chartermi
fgmaloziec@chartermi
4 years ago
Reply to 

Thanks. I ordered the last 3 sample cans on 6/1. Have not received a shipping date as yet.

Avatar photo
4 years ago

Do you recommend sanding with the 80 grit prior to staining?

Avatar photo
Admin
4 years ago
Reply to 

No need to sand.

Avatar photo
4 years ago
Reply to 

Thanks. Can’t wait to get started once we choose a color

Avatar photo
4 years ago
Reply to 

My wife and I have chosen the Trans. Nat Tone for our stain. It’s been a while (two weeks) since I last did anything to the deck. My plan is to give it another power wash, dry 48 hours, and use one coat. Does that seem prudent? The deck just has some bird droppings on it.

Avatar photo
Admin
4 years ago
Reply to 

Yes, correct.

Avatar photo
4 years ago
Reply to 

Ordering 6 gal. of Trans Natural Tone. Best applicator?
Was contemplating stain/paint glove for balusters. Too heavy for decking application?

Avatar photo
Admin
4 years ago
Reply to 

Use deck stain pads or brushes. Those stain gloves can be messy.

Avatar photo
4 years ago
Reply to 

Thanks

John
John
4 years ago

I have a 200 foot cedar fence that was stained a number of years ago with transparent stain. It has weathered a lot but there are still areas of brown stain on the wood and others with no evidence of residual stain. I want to use an oil based semi-solid Armstrong stain on it. The green algae spots have been removed with a cleaner on the entire fence. Do I strip next, or will the semi-solid stain work over what is there.

Avatar photo
Admin
4 years ago
Reply to  John

Could you post a picture here?

John
John
4 years ago
Reply to 

best and worse

Avatar photo
Admin
4 years ago
Reply to  John
Daniel
Daniel
4 years ago

I am about to sand, wash, brighten and then stain some Western red cedar wood wrapped around an outdoor kitchen area. When in the process should the final sanding be completed before straining?

Avatar photo
Admin
4 years ago
Reply to  Daniel

Between stripping and brightening.

DANIEL HOANG
DANIEL HOANG
4 years ago
Reply to 

Thanks for the quick reply! So, I’m assuming since I am not stripping any existing stain, I’m going to perform the following steps?

STEP 1: Sand with 80 grit sandpaper to smooth (which is also removing the natural graying over the past 9 months)

STEP 2: Clean/wash cedar boards with RAD

STEP 3: Sand with 150 grit sandpaper

STEP 4: Brighten cedar boards with RAD

StEP 5: Stain

Avatar photo
Admin
4 years ago
Reply to  DANIEL HOANG

Clean first to remove the gray, lightly sand after with 60-80 grit max, then brighten.

Jeff L
Jeff L
4 years ago

Is there a particular sandpaper grit that should be used if sanding is needed? Does the grit matter if it’s new, replacement wood as opposed to wood on an existing deck?

Avatar photo
Admin
4 years ago
Reply to  Jeff L

60-80 grit. New or older does not matter.

Zoody
Zoody
4 years ago

Hi! I have a 10 year old screened in porch with a mahogany floor. It has not had anything done to the wood in over 6 years and I have no idea what type of stain was used in the past. What do you suggest as my process to revitalize the floor? Does it need to be sanded before staining?
Or should I just use your RAD Wood cleaner and stain remover, don’t sand and then apply the stain? See photo.

Avatar photo
Admin
4 years ago
Reply to  Zoody

Normally you would strip this but you have no way of washing it out so you will have to sand it.

Zoody
Zoody
4 years ago
Reply to 

Thank you! One last question, after sanding do you recommend applying a pre-stain wood conditioner and if so which one?

Avatar photo
Admin
4 years ago
Reply to  Zoody

No need.

Avatar photo
4 years ago

When applying cleaner should wood be wet or dry? Had planned on power washing any loose dirt off of fence before applying the cleaner, would that be ok?

Avatar photo
Admin
4 years ago
Reply to 

Yes, no issues if the wood is wet.

Mikel
Mikel
4 years ago

Hi,

I just finished cleaning my 20yr old cedar deck with RAD stripper and brightener. While it worked well to remove old stain and gray fibers, it also pulled the grain to the surface creating a furry appearance, especially on the spindles and hand rails. Is it required/recommended to remove the fur prior to staining? If so, how would you recommend that be done?

Thanks from MN

Avatar photo
Admin
4 years ago
Reply to  Mikel

No, you do not have to remove this. if you want, you would buff it off with a floor buffer and a sanding pad.

Ed
Ed
4 years ago

Hello. This photo shows new section of fence on the left and old (2.5 years) on the right. *Both* sections were stained with AC Sierra Redwood. They don’t match I think because my contractor did not follow recommendations here when staining the old section (stained a few days after install, no prepping). The new section I waited and followed instructions with RAD cleaner and brightener.

I am ready to re-stain the old section. What steps should I follow? Can I use RAD cleaner and brightener, or do I need to use the stripper product? Thanks!

Avatar photo
Admin
4 years ago
Reply to  Ed

Strip and brighten all.

Ed
Ed
4 years ago
Reply to 

OK, thanks. When you say “all” do you mean the new section, too? I don’t plan to re-stain the new side. If the re-stained doesn’t match the left side, I’ll just let it be.

Avatar photo
Admin
4 years ago
Reply to  Ed

The best way to get it to blend is to redo all but up to you.

Avatar photo
4 years ago

Hi. I’ve a wrap around mahogany porch. In good shape but looking to revitalize. There’s a dark brown/ walnut color I assume is transparent stain. It’s wearing in couple spots but still in tact.

1- So… how do I know for sure it’s not solid stain bc that requires sanding, correct?
2- And assuming its regular transp stain ..to prep for finish I’ll need stain remOver then brightener?

tks very much

Avatar photo
Admin
4 years ago
Reply to 

Send pictures.

Avatar photo
4 years ago
Reply to 

Will soon. I’ll take a couple.. entire porch then I have a 4×4 square I cut for side stair post install. I’ll send underside and top to see difference.

Avatar photo
4 years ago
Reply to 

Pictures of the porch

Avatar photo
Admin
4 years ago
Reply to 

Strip and then brighten for prep.

Avatar photo
4 years ago
Reply to 

Ok. Just 2 more questions and I’ll get out of your stain!

1- So I assume that means it’s transparent stain on it?

2- why is stripping w chemicals better than sanding for hardwood?

3- is the final result (after brightened/oil)the same or better then w sanding?

Tks very much for you responses and pro opinion!

Avatar photo
Admin
4 years ago
Reply to 

1. Semi-transparent.
2. Easier and leaves the wood more porous.
3. Same.

Oregon_Phil
Oregon_Phil
4 years ago

I have a brand new Redwood swingset that had a “water based stain” applied by the swingset manufacturer.
I asked them what brand of stain they used, and they did not know, but they did confirm it was water based.
I would describe the application of that water based stain as “splash and dash”…that is, some corners playset structure have very little, if no, stain.
The structure if extremely clean (new).
What cleaner/stripper product(s)/process do you recommend before I apply your AC semi-transparent redwood stain?

Avatar photo
Admin
4 years ago
Reply to  Oregon_Phil

Post a pictue of the swingset.

Doug Sims
Doug Sims
4 years ago

I have prepared deck. My plan is to apply wet on wet. Can I walk on applied stain?

Avatar photo
Admin
4 years ago
Reply to  Doug Sims

The first coat, yes, but not the second coat.

Melissa
Melissa
4 years ago

I read on the Armstrong site that you did not have to buy a RAD cleaner, you could use bleach and water thus saving time and money.. is that in fact truth?

Avatar photo
Admin
4 years ago
Reply to  Melissa

We do not suggest this on our site as bleach is bad for wood and breaks down the lignin. This is a known issue.

702
0
Would love your thoughts, please comment.x